Troubleshooting
Can I change the mix order of my products?
Currently, the way the system functions is to introduce products into the mix in the order they are listed in the Work Order. Here is a video of how to change the mix order inside the Work Order. Data -> Work Orders -> Open the Work Order that you ...
How does holdback work?
"Holdback" is a function by which the main/carrier valve closes to allow for maximum suction on chemical/product induction. By closing off the carrier (temporarily) all available suction can be dedicated to introducing product(s) to your blend tank ...
How often should I clean my filters?
The most common time to clean filters is when switching crops or at the end of the season. More often will not hurt.
Why am I only seeing 100 records?
You know you have more than 100 records. So, why does it only show 100 records when you run a search? The new Mixmate app's improved blending interface collates large amounts of data during your blend. We use this data to compile the information ...
Why is my continuous flow button not active?
The continuous flow button will be active when there is a container size set on the product. Here is how to set the container size: Data -> Products -> Select the product to change -> Enter the container size value and unit of measure -> Save
How do we achieve essentially a 50% water in the tank by starting many items at the same time?
Mixmate operates differently than the way it used to be done. First lets recap what the traditional way of mixing looks like before we dive into how the Mixmate essentially achieves this same process. The traditional way states that you need to fill ...
Flowmeter Calibration
The carrier meters that are used with the system typically have to be calibrated after final installation because they are sensitve to how the liquid flows through them. We typically like to see how the total comes out over a period of 3 loads before ...
Managing Permissions and Location
You must have Location turned on as well as all permissions accepted for the Mixmate Apps to work. Android ties wifi and location together and will not allow the Mixmate app to connect to the machine without location. Below is a short video showing ...
Rinse pump sizing
The rinse pump is ONLY for pressurizing the inductor. Stacks are NOT to be pressurized due to overspeeding gear meters. Pump specifications: 25 gallons/min at 25 PSI. Maximum 100 PSI. We recommend a self-priming pump. Electric: Typically a 2 HP pump ...
How do I delete my account?
Please email support@praxidyn.com with your account information and we can delete it for you. Data Privacy requires this article.
Direct Drive Small Electric Motor Wiring ( Less than 22 Amps )
IF YOU WANT MANUAL OVERRIDE, YOU MUST WIRE THROUGH A SWITCH BOX. For small motors ( 22 amps or less ) WEG makes a low current coil motor contactor that can be directly driven from a Praxidyn module. Find on Automation Direct The part number for this ...
Terminators Required
Two (2) blue* Terminators are REQUIRED to be connected to your Mixmate CANBUS for your system to run properly. They should be placed as far apart from each other as possible. (opposite ends of the CANBUS) Pro Inductors systems have one installed ...
ARAG Valve CANbus Indicator Light Message
Mixmate power diagnostics
Check battery voltage - minimum is 12.3 Volts. A Maintained battery will be between 12.7 and 13.7 volts. A charging battery will be 13.7 up to 14.7 volts Check screws on back of battery disconnect switch Check fuses Pro Inductor: 15 amp (x2) in fuse ...
CAN Bus Communications Diagnostics
If you are having CAN Bus issues here are the steps to diagnose CAN issues. TERMINATORS REQUIRED Terminators: There should be 2 terminators in the system. With both terminators plugged into the harness and the power shut off, the easiest place to ...
Mag meter not measuring properly
Are power, signal lights lit? Check connection, cabling, plugs are seated securely. Next check in configuration Components to make sure the flowmeter/mag meter is connected to the Module that the flowmeter is Physically connected. Basically there are ...
Slow mix time with thicker chemical(s)
When using a highly viscous chemical, it is possible to add a pump at the tote, so it can push the product into the Mixmate and move things along quicker. Make sure that the overall flowrate stays below 35 gal/min as to not damage gear meter. Lastly, ...